Тратите слишком много денег
за потребление энергии?
Обеспокоены энергозатратными приборами или потреблением определенного помещения?
А как насчет всего вашего дома?
Пришло время уменьшить ваши счета за электроэнергию.
Трехфазный умный измеритель Qubino представляет собой чрезвычайно универсальное и мощное устройство Z-Wave для измерения потребления электроэнергии в трехфазной электрической сети напряжением до 3 х 65А.
Умный способ контролировать потребление трех устройств, одного 3-фазного устройства
или весь ваш в трехфазной сети
Обеспокоены энергозатратными приборами или потреблением определенного помещения?
А как насчет всего вашего дома?
Пришло время уменьшить ваши счета за электроэнергию.
Уменьшите количество энергии, которую вы используете. С 3-фазным интеллектуальным счетчиком Qubino вы можете дистанционно измерять энергопотребление вашего дома.
... измерить энергопотребление всего вашего дома, одного трехфазного устройства, трех независимых устройств или трех групп устройств.
Самый точный в мире трехфазный умный счетчик электроэнергии Z-Wave.
Это единственный трехфазный счетчик электроэнергии на рынке, через который проходит ток.
Текущие зажимы не нужны.
Он измеряет намного больше чем Вт и кВтч.
Он измеряет 9 различных значений:
В, А, Вт, var, PF, кВтч импорт, кВтч экспорт, кВАч, кВАрч.
Добавляя дополнительные контакторы IKA или BICOM, 3-фазный интеллектуальный счетчик Qubino может автоматически отключать устройства после того, как они превысят установленное энергопотребление.
Например, отопление автоматически отключится после того, как достигнет установленного значения потребляемой мощности.
Модуль может управлять двумя электрическими устройствами (обеспечивает включение/выключение):
Трехфазный умный счетчик Qubino поддерживает самую продвинутую на рынке систему безопасности для интеллектуальных домашних устройств: защищенный протокол беспроводной связи S2.
Чем больше диапазон действия, тем более надежным является продукт - устройство имеет первоклассную антенну. Оптимизированное для надежности, это устройство может взаимодействовать беспроводным способом на расстояния более 150 метров.
Лучше антенна. Лучше Z-Wave. Устройство разработано на технологии Z-Wave Plus последнего 5го поколения, чтобы предоставить вам самое быстрое время отклика и оптимальное время жизни батареи между перезарядками.
Если вы используете устройство для обеспечения безопасности, вы хотите чтобы взаимодействие было защищенным. Вот почему устройство использует беспроводное шифрование AES-128 для защиты от несанкционированного доступа и хакеров.
Используете ли вы устройство для комфорта или безопасности, вы желаете чтобы оно всегда оставалось обновленным до последней версии. Как бы не создавались обновления прошивки для устройства, вы всегда можете обновить его с помощью Microsoft Windows или выбрать Z-Wave контроллер.
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
40 | 1 | Reporting on power change | 1 to 100 (Default) |
1% - 100% reporting enabled.Power report is send only when actual power in Watts (in real time changes for more than set percentage comparing to previous Active Power, step is 1%. | |
0 | reporting disabled | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
42 | 1 | Reporting on time interval | 0 | Reporting disabled | |
600 to 32535 (Default) |
600-32535 = 600 (600 seconds – 32535 seconds). Reporting enabled. Report is send with the time interval set by entered value. | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
43 | 2 | Other Values - Reporting on time interval | 0 | Reporting disabled | |
600 to 32535 (Default) |
(600 seconds – 32535 seconds). Reporting enabled. Report is send with the time interval set by entered value. |
Group ID | Group Profile Name | Profile | Maximum Nodes | Description | Endpoint ID | Commands |
---|---|---|---|---|---|---|
1 | 1 | Supports the following commands: • Device Reset Locally: triggered upon request • Meter Report: triggered according to Configuration parameters 40,42 and 43 | 0 |
|
Supported Command Classes |
Command Class Association Group Info V2 |
Command Class Association V2 |
Command Class Configuration |
Command Class CRC16 Encap |
Command Class Device Reset Locally |
Command Class Manufacturer Specific V2 |
Command Class Meter V4 |
Command Class Multi Channel Association V3 |
Command Class Multi Channel V4 |
Command Class Powerlevel |
Command Class Security |
Command Class Security 2 |
Command Class Supervision |
Command Class Transport Service V2 |
Command Class Version V2 |
Command Class Z-Wave+ Info V2 |
Parameter no. 7 – Input 1 switch function selection
Available configuration parameters for input switch I1
Values (size is 1 byte dec):
Default value 0
NOTE: By setting the parameter 7 to value 4 or 5 the external Relay (IKA) is working with input switch without enabling parameter no. 101
NOTE: To make the IR Relay (BICOM) responsive to the digital input, in addition to the setting of the configuration parameter 7, parameter 100 must also be set to value 1 or 2.
Parameter no. 40 – Reporting on power change
This parameter is valid for Active Power Total, Active Power Phase1, Active Power Phase2 and Active Power Phase3.
Set value means percentage from 0-100 = 0% - 100%
Available configuration parameters (data type is 1 Byte DEC):
NOTE: if power change is less than 5 W, the report is not send (pushed).
NOTE: Device is measuring also some disturbances even if on the output is no load. To avoid disturbances:
The module is measuring some disturbances even if on the output is no load. To avoid unintended reporting: If measured active power (W) is below 5 W -> the value is not reported.
Parameter no. 42 – Reporting on time interval
This parameter is currently valid only for Active Energy Total Import/Export (kWh), Reactive Energy Total (kvarh), Total Energy (kVAh)
Available configuration parameters (data type is 2 Byte DEC)
• Default value 600 (600 seconds - 10 minutes)
• 0 – reporting disabled
• 600-32535 = 600 (600 seconds – 32535 seconds). Reporting enabled. Report is send with the time interval set by entered value.
NOTE: Device is reporting only if there was a change of 0.1 in Energy
NOTE: In the future will be possible to measure and report also Active Energy on PH1, PH2 and PH3.
Parameter no. 43 – Other Values - Reporting on time interva
This parameter is valid only for Voltage (V of ph1, ph2, ph3), Current (A of ph1, ph2, ph3), Total Power Factor, Total Reactive Power (var)
Available configuration parameters (data type is 2 Byte DEC)
• Default value 600 (600 seconds - 10 minutes)
• 0 – reporting disabled
• 600-32535 = 600 (600 seconds – 32535 seconds). Reporting enabled. Report is send with the time interval set by entered value.
• Note: Device is reporting only if there was a change
Parameter no. 100 – Enable / Disable External IR relay (BICOM)
Available configuration parameters (data type is 1 Byte DEC):
• default value 0
• 0 – External IR relay disabled
• 1 – External IR relay enabled and connected to all 3 Phases
• 2 – External IR relay enabled and connected to a Phase 1
NOTE1: After parameter change, first exclude module (without setting parameters to default value) and then re include the module.
NOTE 2: If you don't have IR BICOM relay module mounted and you enable IR communication (parameter 100 is 1 or 2) there will be no valid IR relay state reported. It will be reported IR COMMUNICATION ERROR and LED2 will BLINK.
Parameter no. 101 – Enable / Disable External relay (IKA)
Available configuration parameters (data type is 1 Byte DEC):
• default value 0
• 0 – External relay disabled
• 1 – External relay enabled and connected to Phase 2
NOTE1: After parameter change, first exclude module (without setting parameters to default value) and then re include the module.
Parameter no. 106 – External IR relay (BICOM) power threshold settings – maximum power of all phases together
This parameter defines a threshold when External IR relay is being turned off. (If Parameter no. 100 is set to the value 1 or 2)
Available configuration parameters (data type is 2 Byte DEC)
Default value 0
0 – no function
10-60000 – 10W-60000W
NOTE: Meter is capable of measuring max 3x65A!
Parameter no. 107 – External relay (IKA) power threshold settings – maximum power on phase L2
This parameter defines a threshold when External relay is being turned off (if the parameter no. 100 is set to the value 1 or 2).
Available configuration parameters (data type is 2 Byte DEC)
• Default value 0
• 0 – no function
• 10-20000 – 10W-20000W
NOTE: Meter is capable of measuring max 65A
Parameter no. 112 – Power threshold – Delay before power on
External IR relay/ External relay is turned off due to detected overload (as set by parameter 106&107) and remains off for a time, defined in this parameter. After that time, the output turns on to check, if the overload is still present.
Available configuration parameters (data type is 2 Byte DEC)
• Default value 0 (disabled)
• 0 – External IR relay/ External relay will not turn back on
• 30 – 32535 = 30 s – 32535 s
NOTE: the delay time may be prolonged for more then 10s of the time set by the parameter.
L1I, L2I, L3I | Live input |
NI | Neutral input |
L1O, L2O, L3O | Live output |
No | Neutral output |
16 | Input for IR external relay/Ext. relay |
15 | Output for External relay (max. 3W) |
S | Service button (used to add or remove device from the Z-Wave network) |
LED1 | Device status. For detailed information please check the chapter “LED SIGNALIZATION FOR INCLUSION/EXCLUSION” |
LED2 | External relay status. For detailed information please check chapter LED SIGNALIZATION FOR INCLUSION/EXCLUSION |
IR | Output for IR external relay (BICOM) |
1000imp/kWh | Red - Pulse rate (On – no load indication) |
Технология | Z-Wave+ |
---|---|
Z-Wave Plus: | Да |
Security S2 Classes | S2 Authenticated, S2 Unauthenticated |
Z-Wave аппаратная платформа | ZM5202 |
Z-Wave тип библиотеки | Enhanced 232 Slave |
Z-Wave тип устройства | Whole Home Meter - Simple |
Z-Wave тип роли | Always On Slave |
Производитель | Qubino |
Группы ассоциаций | 1 |
Z-Wave Функции | Multichanel , Multichannel Association, Power Level |
Максимальная нагрузка | 65A |
Внутренняя/наружная установка | Внутренняя, Наружная |
Источник питания | Кабель AC |
Назначение | Управление энергоснабжением |
OTA обновление прошивки | Да |
Форм-фактор | DIN рейка |